Inflatable Restraint Roof Side Rail Module Replacement - Front RHD
Removal Procedure
Caution: Refer to SIR Caution in the Preface section.
Caution: Refer to SIR Inflator Module Handling and Storage Caution in the Preface section.
- Disable the SIR system. Refer to
SIR Disabling and Enabling
.
- Remove the windshield garnish moulding. Refer to
Windshield Garnish Molding Replacement
.
- Remove the sunshade from the headliner. Refer to
Sunshade Replacement
.
- Remove the assist handles from the headliner. Refer to
Assist Handle Replacement
.
- Remove the lower centre pillar trim panel. Refer to
Center Pillar Lower Trim Panel Replacement
.
- Remove the upper centre pillar trim panel. Refer to
Center Pillar Upper Trim Panel Replacement
.
- Remove the rear window shelf trim panel. Refer to
Rear Window Shelf Trim Panel Replacement
.
- Remove the rear quarter pillar trim panel. Refer to
Quarter Lower Rear Trim Panel Replacement
.
- Remove the rear quarter pillar trim panel. Refer to
Quarter Upper Trim Panel Replacement
.
- Lower the headliner in order to gain access to the roof rail module. Refer
to
Headlining Trim Panel Replacement
.
- Disconnect the harness connector (1)
from the roof rail module.
- Remove the following roof rail bolts in
sequence (5), (4), (3), and (2), then unhook the tether (1).
- With the aid of an assistant lift the roof rail upwards towards the roof
making sure to un-hook the mounting points on the roof.
- For deployment procedure. Refer to
Inflator Module Handling and Scrapping
.
Installation Procedure
Caution: Refer to SIR Caution in the Preface section.
Caution: Refer to SIR Inflator Module Handling and Storage Caution in the Preface section.
Caution: In order to prevent accidental deployment of the air bag which could
cause personal injury, do not dispose of an undeployed inflator module as
normal shop waste. The undeployed inflator module contains substances that
could cause severe illness or personal injury if the sealed container is damaged
during disposal. Use the following deployment procedures to safely dispose
of an undeployed inflator module. Failure to dispose of an inflator module
as instructed may be a violation of federal, state, province, or local laws.
- Remove any dirt, grease, or other impurities from the mounting surface.
- With the aid of an assistant carefully replace the roof rail upwards towards
the roof making sure the hooks are seated correctly in place on the roof.
- Install the mounting fasteners to the inflatable
restraint roof rail module in the following order (2), (3), (4), (5)
and then the tether hook (1).
Tighten
Tighten the fasteners to 6 N·m (53 lb in).
- Re-connect the harness connector (1)
to the roof rail module.
- Raise the headliner. Refer to
Headlining Trim Panel Replacement
.
- Install the rear quarter pillar trim panel. Refer to
Quarter Upper Trim Panel Replacement
.
- Install the rear quarter pillar trim panel. Refer to
Quarter Lower Rear Trim Panel Replacement
.
- Install the rear window shelf trim panel. Refer to
Rear Window Shelf Trim Panel Replacement
.
- Install the upper centre pillar trim panel. Refer to
Center Pillar Upper Trim Panel Replacement
.
- Install the lower centre pillar trim panel. Refer to
Center Pillar Lower Trim Panel Replacement
.
- Install the windshield garnish moulding. Refer to
Windshield Garnish Molding Replacement
.
- Install the sunshade from the headliner. Refer to
Sunshade Replacement
.
- Install the assist handles from the headliner. Refer to
Assist Handle Replacement
.
- Enable the SIR system. Refer to
SIR Disabling and Enabling
.
- If re-programming is required. Refer to
Control Module References
.