GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2003 🢒 Corvette 🢒 Restraints 🢒 SIR 🢒 Ignition Switch Housing Bracket Replacement

Removal Procedure
  1. Remove the console. Refer to Console Replacement .

    2. Object Number: 95715 Size: SH
  2. Remove the IP accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
  3. Remove the driver knee bolster trim panel. Refer to Driver Knee Bolster Panel Replacement .
  4. Remove the IP upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement .
  5. Remove the ignition switch lock cylinder. Refer to Ignition Switch Lock Cylinder Replacement .
  6. Remove the bolts retaining the ignition switch to the ignition switch housing bracket.
  7. Reposition the ignition switch.

    8. Object Number: 95661 Size: SH
  8. Remove the inside air temperature sensor aspirator duct, if equipped.
    9. 8.1. Depress the duct retaining tab and remove the duct from the ignition switch housing bracket.
    8.2. Use a twisting motion to release the duct from the duct muffler.

    Object Number: 95679 Size: SH

    Important: The following step must be performed to assure proper trim fits during installation.

  9. Mark the location of the ignition switch housing bracket. Refer to Instrument Panel Disassembly Precautions .
  10. Remove the bolt retaining the ignition switch housing bracket to the steering column bracket.

    11. Object Number: 95676 Size: SH
  11. Remove the bolts retaining the ignition switch housing bracket to the IP center support bracket.
  12. Remove the ignition switch housing bracket.

Installation Procedure

    Object Number: 95676 Size: SH
  1. Install the ignition switch housing bracket into position as marked prior to removal.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the bolts retaining the ignition switch housing bracket to the IP center support bracket.

    3. Tighten
    Tighten the ignition switch housing bracket to IP center support bracket bolts to 12 N·m (106 lb in).


    Object Number: 95679 Size: SH
  3. Install the bolt retaining the ignition switch housing bracket to the steering column bracket.

    4. Tighten
    Tighten the ignition switch housing bracket to steering column bracket bolt to 1.9 N·m (17 lb in).


    Object Number: 95661 Size: SH
  4. Install the inside air temperature sensor aspirator duct, if equipped.
    5. 4.1. Use a twisting motion to secure the duct to the duct muffler.
    4.2. Install the duct retaining tab to the ignition switch housing bracket.

    Object Number: 95715 Size: SH
  5. Install the ignition switch to the ignition switch housing bracket.
  6. Install the ignition switch retaining bolts.

    7. Tighten
    Tighten the ignition switch retaining bolts to 5.5 N·m (49 lb in).

  7. Install the ignition switch lock cylinder. Refer to Ignition Switch Lock Cylinder Replacement .
  8. Install the IP upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement .
  9. Install the driver knee bolster trim panel. Refer to Driver Knee Bolster Panel Replacement .
  10. Install the IP accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
  11. Install the console. Refer to Console Replacement .