GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2006 🢒 Equinox 🢒 Engine 🢒 Engine Mechanical - 3.4L 🢒 Engine Front Cover Replacement

Removal Procedure
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
  3. Install the engine support fixture. Refer to Engine Support Fixture .
  4. Remove the drive belt. Refer to Drive Belt Replacement .
  5. Drain the cooling system. Refer to Cooling System Draining and Filling .
  6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  7. Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement .
  8. Remove the lower belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Lower .
  9. Remove the engine oil pan. Refer to Oil Pan Replacement .
  10. Lower the vehicle.
  11. Remove the left belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Left Side .

    12. Object Number: 1401247 Size: SH
  12. Remove the right engine mount bracket bolts (2-4).
  13. Remove the right engine mount bracket (1).
  14. Remove the water pump. Refer to Water Pump Replacement .
  15. Remove the thermostat bypass hose adapter. Refer to Thermal Bypass Fitting Replacement .
  16. Remove the radiator outlet hose from the engine front cover. Refer to Radiator Outlet Hose Replacement .

    17. Object Number: 1401296 Size: SH
  17. Remove the engine front cover bolts (2-4).
  18. Remove the engine front cover (1).

    19. Object Number: 1401299 Size: SH
  19. Remove the engine front cover gasket (1).
  20. Clean the engine block and front cover gasket sealing surfaces.

Installation Procedure

    Object Number: 61819 Size: SH
  1. Apply sealer to the lower tabs of the engine front cover gasket. Refer to Adhesives, Fluids, Lubricants, and Sealers for the correct part number. Uniformly apply the sealer to both sides of the gasket lower tabs with the sealant bead being no less than 5.0 mm (0.20 in) wide as shown. Torque front cover immediately after installation of sealer coated gasket.

    2. Object Number: 1401299 Size: SH
  2. Install the gasket (1) to the engine block positioning the gasket on the locating pins (2).

    3. Object Number: 1401296 Size: SH
  3. Install the engine front cover (1) to the engine block aligning the cover with the locating pins.

    4. Notice: Refer to Fastener Notice in the Preface section.

  4. Install the engine front cover bolts (3, 4).

    5. Tighten
    Tighten the bolts to 55 N·m (41 lb ft).

  5. Install the engine front cover bolts (2).

    6. Tighten
    Tighten the bolts to 27 N·m (20 lb ft).

  6. Install the radiator outlet hose to the engine front cover. Refer to Radiator Outlet Hose Replacement .
  7. Install the thermostat bypass hose adapter. Refer to Thermal Bypass Fitting Replacement .
  8. Install the water pump. Refer to Water Pump Replacement .

    9. Object Number: 1401247 Size: SH
  9. Install the right engine mount bracket (1).
  10. Install the right engine mount bracket bolts (2-4).

    11. Tighten
    Tighten the bolts to 55 N·m (41 lb ft).

  11. Install the engine mount bracket bolts (3).

    12. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).

  12. Install the left belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Left Side .
  13. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  14. Install the engine oil pan. Refer to Oil Pan Replacement .
  15. Install the lower belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Lower .
  16. Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement .
  17. Lower the vehicle.
  18. Install the drive belt. Refer to Drive Belt Replacement .
  19. Remove the engine support fixture.
  20. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
  21. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  22. Fill the cooling system. Refer to Cooling System Draining and Filling .