Table 1: | APP Sensor Position Table |
The accelerator pedal position (APP) sensor is mounted on the accelerator pedal control assembly. The sensor is made up of 3 individual sensors within 1 housing. Three separate signal, low reference, and 5-volt reference circuits are used in order to interface the APP sensor with the engine control module (ECM). Each sensor has a unique functionality to determine the pedal position as shown in the table below. The ECM uses the APP sensor to determine the amount of acceleration or deceleration desired by the person driving the vehicle via the fuel injector control. If the ECM determines high voltage in the APP sensor 1 circuit, DTC P2123 sets.
APP Sensor | Actual Pedal Position | % Depressed as Observed on a Scan Tool | Voltage as Observed on a Scan Tool |
---|---|---|---|
1 | Pedal at rest | 0 | .52 - .80 |
1 | Pedal at full travel | 100 | 2.12 - 2.78 |
2 | Pedal at rest | 0 | 4.25 - 4.53 |
2 | Pedal at full travel | 100 | 2.24 - 2.93 |
3 | Pedal at rest | 0 | 3.95 - 4.13 |
3 | Pedal at full travel | 100 | 2.69 - 3.16 |
This diagnostic procedure supports the following DTC:
DTC P2123 Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
• | DTCs P0642 or P0643 are not set. |
• | The ignition switch is in the Crank or Run position. |
• | The ignition voltage is between 7-16 volts. |
• | The APP sensor 1 voltage is more than 4.75 volts. |
• | The above condition is present for less than 1 second. |
• | The control module stores the DTC information into memory when the diagnostic runs and fails. |
• | The malfunction indicator lamp (MIL) will not illuminate. |
• | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records. |
• | If one or more APP sensor DTCs are set for a single APP sensor, the following occurs: |
- | The control module will not command Reduced Engine Power mode. |
- | The control module will use the remaining two APP sensors to calculate throttle response. |
• | If certain multiple APP sensor DTCs are set for more than one APP sensor, the following occurs: |
- | The control module commands Reduced Engine Power mode. |
- | The APP indicated angle is limited to a predetermined value to limit the amount of throttle control. |
- | The message center displays Reduced Engine Power. |
• | If all three APP sensors are out of range, the following occurs: |
- | The control module commands Reduced Engine Power mode. |
- | The APP indicated angle is limited to 0 percent. The control module only allows the engine to idle. |
- | The message center displays Reduced Engine Power. |
• | A current DTC Last Test Failed clears when the diagnostic runs and passes. |
• | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
• | Clear the DTC with a scan tool. |
Step | Action | Values | Yes | No |
---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Engine Controls? | -- | Go to Step 2 | |
2 |
Does the DTC fail this ignition? | -- | Go to Step 4 | Go to Step 3 |
3 |
Did this DTC fail this ignition during the above test? | -- | Go to Step 9 | Go to Intermittent Conditions |
4 |
Does the scan tool indicate the APP sensor 1 voltage at the specified value? | 0 V | Go to Step 5 | Go to Step 6 |
5 |
Does the scan tool indicate APP sensor 2 voltage at the specified value? | 0 V | Go to Step 10 | Go to Step 8 |
6 |
Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 7 |
7 |
Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 |
8 |
Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 |
9 | Repair the intermittent condition as necessary. Refer to Connector Repairs and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 14 | -- |
10 | Inspect for poor connections at the harness connector of the APP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 12 |
11 | Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 |
12 | Replace the APP sensor assembly. Refer to Accelerator Pedal Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- |
13 | Replace the ECM. Refer to Engine Control Module Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- |
14 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 15 |
15 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK |