The Throttle Position (TP) sensor provides a voltage signal which changes relative to the throttle blade angle. The signal voltage varies from about 0.5 volt at idle to about 4.0 volts at Wide Open Throttle (WOT).
The TP signal is one of the most important inputs used by the VCM for fuel control and for most of the VCM control outputs. This DTC is a type D DTC
• | The engine is running. |
• | The TP sensor signal voltage is greater than about 4.7 volts |
The VCM stores the DTC in History if the VCM detects an intermittent problem.
The VCM turns OFF the MIL after 3 consecutive driving trips without a fault condition present. A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles (the coolant temperature has risen 22°C (40°F) from the start-up coolant temperature and the engine coolant temperature exceeds 71°C (160°F) during that same ignition cycle) or the scan tool clearing feature has been used.
The VCM pins GRY 12 and GRY 27 are spliced together inside of the VCM. When checking one of these circuits for a problem, also check the other circuit and the components on the circuit.
The scan tool reads the throttle position in volts. The scan tool should read about 0.45 to 0.85 volt with the throttle closed and the ignition switch turned ON or at idle. The voltage should increase at a steady rate as the throttle is moved toward the Wide Open Throttle (WOT).
Also, some scan tools will read the throttle angle. 0% = closed throttle. 100% = WOT.
Scan the TP sensor while depressing the accelerator pedal with the engine turned OFF and the ignition turned ON. The display should vary from below the 1.25 volts (1250 mV) when the throttle is closed to over 4.5 volts (4500 mV) when the throttle is held at WOT position.
A DTC P0123 will result if the TP ground circuit is open or the TP signal circuit is shorted to the voltage.
A DTC P0122 will result if there is an open or a short to ground in the 5 volt reference circuit or the TP sensor signal circuit.
Refer to Intermittent Conditions .
The numbers below refer to the step numbers in the diagnostic table.
If the TP signal is greater than 4.8 volts, then the fault is present.
With the TP sensor disconnected, the TP signal voltage should go low if the VCM and wiring is OK.
Probing the TP sensor ground circuit with a test lamp checks the 5 volt return circuit. This step isolates a malfunctioning sensor, VCM or an open TP sensor ground circuit.
Step | Action | Value(s) | Yes | No |
---|---|---|---|---|
1 |
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records for reference. This data will be lost when the Clear Info function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
Does the scan tool display the TP sensor signal to be greater than the specified value. | 4.8V | |||
Disconnect the TP sensor. Does the scan tool display a TP sensor signal below the specified value? | 0.2V | |||
Probe the TP sensor ground circuit with a test lamp connected to B+. Is the test lamp on? | -- | |||
5 | Is the DTC P0108 also set? | -- | Go to DTC P0108 Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage | |
6 | The DTC is intermittent. If no additional DTCs are stored, refer to the Diagnostic Aids. If any additional DTCs are stored, refer to those tables. Are there any additional DTCs stored? | -- | Go to the applicable DTC table | |
7 | Check the connections at the TP sensor. Was a problem found? | -- | ||
8 | Check for a short to voltage in the TP sensor signal circuit. Was a problem found? | -- | ||
9 | Check for an open in the TP sensor ground circuit. Was a problem found? | -- | -- | |
10 | Repair the circuit as necessary. Refer to Wiring Repair in Engine Electrical. Is the action complete? | -- | -- | |
11 | Replace the TP sensor. Refer to TP Sensor Replacement . Is the repair complete? | -- | -- | |
12 | Replace the VCM. Important: When replacing the VCM, the new VCM will need to be programmed. Refer to VCM Replacement/Programming . Is the repair complete? | -- | -- | |
13 |
Does the scan tool indicate that this diagnostic ran and passed? | -- | ||
14 | Use the scan tool in order to display the Capture Info and the Review Info. Are there any DTCs displayed that have not been diagnosed? | -- | Go to the applicable DTC table | System OK |