Circuit Description
The throttle position (TP) sensors 1 and 2 are located within the throttle body assembly. The TP sensors share a common 5-volt reference circuit and a common low reference circuit. The 5-volt reference circuit is also shared with the accelerator pedal position (APP) sensor 2. The 5-volt reference voltage is supplied on 2 separate engine control module (ECM) terminals, but the terminals are connected internally to the same voltage supply. Each TP sensor has an individual signal circuit, which provides the ECM with a signal voltage proportional to throttle the plate movement. When the throttle plate is in the closed position, the TP sensor 1 signal voltage is near the low reference and increases as the throttle plate is opened. The TP sensor 2 signal voltage at closed throttle is near the 5-volt reference and decreases as the throttle plate is opened. If the ECM detects the TP sensor 2 signal voltage is less than 0.16 volt, DTC P0222 sets.
Conditions for Running the DTC
| • | The battery voltage is more than 8 volts. |
| • | The engine speed is more than 1,320 RPM. |
Conditions for Setting the DTC
The TP sensor 2 voltage is less than 0.16 volt for more than 140 milliseconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
The ECM performs a comparison of the signals from both TP sensors during the entire range of operation. If the DTC does not set with the key ON and the accelerator pedal released, the actuation of the throttle may cause the DTC to set.
-
The 5-volt reference for the TP sensors and the APP sensor 2 are connected inside the ECM. This step is to determine if the APP sensor is affecting the 5-volt reference circuit of the TP sensors.
Step | Action | Values | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||||
2 |
Is the TP sensor 2 voltage less than the specified value? | 0.2 V | Go to Step 5 | Go to Step 3 | ||||||||
3 |
Does the DTC fail this ignition? | -- | Go to Step 5 | Go to Step 4 | ||||||||
Does the DTC fail this ignition? | -- | Go to Step 14 | Go to Intermittent Conditions | |||||||||
5 |
Is the voltage within the specified range? | 4.8-5.2 V | Go to Step 6 | Go to Step 7 | ||||||||
6 |
Is the voltage within the specified range? | 4.8-5.2 V | Go to Step 11 | Go to Step 9 | ||||||||
Is the voltage within the specified range? | 4.8-5.2 V | Go to Step 13 | Go to Step 8 | |||||||||
8 |
Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 10 | ||||||||
9 |
Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 | ||||||||
10 | Test the 5-volt reference circuit of the APP sensor 2 for a short to ground. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 | ||||||||
11 | Test for an intermittent and for a poor connection at the TP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 | ||||||||
12 | Test for an intermittent and for a poor connection at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 15 | ||||||||
13 | Replace the APP sensor. Refer to Accelerator Pedal Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 16 | -- | ||||||||
14 | Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement? | -- | Go to Step 16 | -- | ||||||||
15 | Replace the engine control module (ECM). Refer to Engine Control Module Replacement . Did you complete the replacement? | -- | Go to Step 16 | -- | ||||||||
16 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 17 | ||||||||
17 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |||||||||
