GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 1999 🢒 Corvette 🢒 Body and Accessories 🢒 Wiring Systems 🢒 Power Seats System Check

Power Seat System Check

Step

Action

Normal Result(s)

Abnormal Result(s)*

1
  1. Turn the ignition switch to the OFF position.
  2. Install the scan tool.
  3. Turn the ignition switch to the ON position.
  4. Select display DTC function with the scan tool.
  5. Check for any stored DTCs related to either DOOR or SEAT operation.

No DTCs are stored in memory or current status.
    • DTC is stored in memory or current status (refer to appropriate DTC table).

2
  1. Turn ignition to the OFF position.
  2. Remove the scan tool from the diagnostic link connector.
  3. Check the driver's side power seat operation.
  4. Press the driver's side seat control button in the following order:
    5. • Seat forward adjust.
    • Seat rearward adjust.
    • Front vertical adjust up.
    • Front vertical adjust down.
    • Rear vertical adjust up.
    • Rear vertical adjust down.
    • Driver's seat moves to the forward position.
    • Driver's seat moves to the rearward position.
    • Front of driver's seat moves upward.
    • Front of driver's seat moves downward.
    • Rear of driver's seat moves upward.
    • Rear of driver's seat moves downward.
    •  Power Seat Inoperative

3
  1. Check the passenger's side power seat operation (if equipped).
  2. Press the passenger's side seat control button in the following order:
    3. • Seat forward adjust.
    • Seat rearward adjust.
    • Front vertical adjust up.
    • Front vertical adjust down.
    • Rear vertical adjust up.
    • Rear vertical adjust down.
    • Passenger's seat moves to the forward position.
    • Passenger's seat moves to the rearward position.
    • Front of passenger's seat moves upward.
    • Front of passenger's seat moves downward.
    • Rear of passenger's seat moves upward.
    • Rear of passenger's seat moves downward.
    •  Power Seat Inoperative

4
  1. Check the driver's seat lumbar operation (if equipped).
  2. Press the driver's side seat control buttons in the following order:
    3. • Upper lumbar inflate.
    • Upper lumbar deflate.
    • Lower lumbar inflate.
    • Lower lumbar deflate.
    • Side bolster inflate.
    • Side bolster deflate.
    • Driver's side upper lumbar inflates.
    • Driver's side upper lumbar deflates.
    • Driver's side lower lumbar inflates.
    • Driver's side lower lumbar deflates.
    • Driver's side bolsters inflate.
    • Driver's side bolsters deflate.

5
  1. Check the passenger's seat lumbar operation (if equipped).
  2. Press the passenger's side seat control buttons in the following order:
    3. • Upper lumbar inflate.
    • Upper lumbar deflate.
    • Lower lumbar inflate.
    • Lower lumbar deflate.
    • Side bolster inflate.
    • Side bolster deflate.
    • Passenger's side upper lumbar inflates.
    • Passenger's side upper lumbar deflates.
    • Passenger's side lower lumbar inflates.
    • Passenger's side lower lumbar deflates.
    • Passenger's side bolsters inflate.
    • Passenger's side bolsters deflate.

6
  1. Turn the ignition switch to the ON position.
  2. Engine is OFF, vehicle is in park/neutral and not moving.
  3. Move the driver's seat to the full rear position.
  4. Depress and hold the Memory 1 button until the memory indicator flashes once.
  5. Move the driver's seat to the full front position.
  6. Depress and hold the Memory 2 button until the memory indicator flashes once.
  7. Choose one other alternate seat position that is different from the two previous settings.
  8. Depress and hold both the Memory 1 and Memory 2 button until the memory indicators flash once.
    • The Memory 1 indicator will glow steady for one second and then flash once when the position for Memory 1 is completed.
    • Memory 1 is set in the full rear position.
    • The Memory 2 indicator will glow steady for one second and then flash once when the position for Memory 2 is completed.
    • Memory 2 is set in the full front position.
    • The Memory 1/2 indicators will glow steady for one second and then flash once when the position for Memory 1/2 is completed.
    • Memory 1/2 is set in the designation of the technician's choice.

7

Now test the Memory switch functions as follows:

    • Depress the Memory 1 button.
    • Depress the Memory 2 button.
    • Depress the Memory 1 and Memory 2 buttons simultaneously.
    • The driver's side seat will move into Memory position 1 which is in the full rear position.
    • The driver's side seat will move into Memory position 2 which is in the full front position.
    • The driver's side seat will move into Memory position 1/2 which is set in the designation of the technician's choice.

* Refer to the appropriate symptom diagnostic table for the applicable abnormal result.